Description
| ITEM | EP-140 |
| Ratio | 1:1.5/1:1.93 |
| Teeth | 21/14 27/14 |
| Module | 5.7 /5.64 |
| Power(HP) | 60 |
| Rated Input | 540rpm |
| Input/Output Description | 1-3/8 Z6 Taper spline |
| Weight(N.W) | 30KG |
The same is true when you move in a wet, muddy environment. You need a lawn mower that allows you to cross obstacles, not just spin the wheels or get stuck on a slope. You need a lot of power and torque to move while maintaining traction. However, when you accelerate, you need less torque to continue.
The mower transmits power from the engine to the wheels and is responsible for changing the torque according to the conditions to control the vehicle speed.
How To Change Lawn Mower Gearbox Oil?
Mower manufacturers usually use 20W-50 oil in the transmission. There is a better alternative to oil in hydrostatic transmissions. The oil in the mower hydrostatic transmission will handle the load well.
The hydraulic gear transmission and pump shall be filled with 20W-50 synthetic oil or 15W-50 engine oil. The machine with an oil reservoir is installed on the frame behind the seat, making it easy to access and check the oil level.
Add a few drops of SAE 30 oil to each pivot point on the linkage to ensure proper operation. It shall include a brake pedal, clutch, and lifting linkage. The Minnesota Department of Agriculture recommends that the riding mower be lubricated every 10 hours and stored after mowing.
Manual transmissions usually require an oil change every 30000 to 50000 miles (48000 to 80000 km). If you want to change the transmission oil filter, please change it simultaneously. Changing the oil after repairing the gearbox leakage is the best way to ensure it is filled.
Changing the transmission oil requires the same treatment standard as changing the engine oil. It is not a good idea to dispose of the oil discharged from the garbage because it is a chemical waste.
Under normal driving conditions, each vehicle can travel 80000 miles on average before changing the gear oil. When using contaminated oil, insufficient lubrication may cause severe damage to the transmission, transfer case, or differential. In addition, if the transfer case or differential has been repaired recently, the gear oil should be replaced.
The transmission dipstick should be located in the user’s Manual (where it should be displayed).
The dipstick should be pulled out of the filler pipe
Make sure the oil color is correct.
What oil did you put in the transmission of the lawn mower?
Mower manufacturers usually use 20W-50 oil in the transmission. There is a better oil alternative in hydrostatic transmission.
PTO shafts for agricultural gearboxes are available.
Agricultural equipment includes various PTO shafts. Each is connected by yokes at both ends and rotates between 540 and 1000 rpm. Safety guards are usually installed on both ends of the PTO shaft to protect the operator. These shields are also present in tractors and farm implements to ensure maximum efficiency. The use of inner yokes also increases safety.
The agricultural PTO transmission is designed to change the output speed of the PTO drive shaft. It can be used as a reduction ratio or an increased ratio gearbox. The reduction ratio gearbox reduces the PTO shaft’s speed from 1000 rpm to 540 rpm, allowing you to use equipment designed for 540 rpm. On the other hand, the agricultural gearbox with an increased transmission ratio increases the speed of the PTO shaft from 540 rpm to 1000 rpm.
Usage Scenario of Lawn Mower Gearbox
Other Agricultural Gearboxes
Agricultural Gearbox Production Workshop
Hangzhou Ever-power Transmission Machinery Co., Ltd. was established in 2006. The company is located in Hangzhou, Zhejiang Province. It has 90 employees and covers an area of 3800 meters. The annual output value is 40 million yuan. The company is committed to R & D; D. Manufacturing and personnel training of various gearboxes, reducers, and construction machinery, including spiral bevel gearboxes, spur gear boxes, worm gearboxes, and cylindrical gearboxes. It also includes a variety of high-pressure cast valve bodies and shell products. Its products are used in various applications, such as agricultural lawn mowers, snow sweepers, fertilizer applicators, grain conveyors, industrial equipment, oil mining machinery, marine industrial equipment, and hydraulic engineering components. More than 95% of its products are exported to Europe, the United States, and Australia. Asia and Canada. The company has a strong technical force and R & D strength; D ability to produce reliable and high-quality products, pursue a unique business philosophy and enjoy a high reputation in the manufacturing industry. Please contact us by phone or email.
edited by hyw
